Lage verzendkosten     Snelle Levering       Korting tot 10%         Bestelinfo       Hulp Nodig?           Inloggen

Prometheus Copper Clay

Prometheus Copper Clay

Prometheus® Copper Clay
Only 30 minutes at 920°C or 90 minutes at 850°C or 10 minutes with a Torch

We are now pleased to present you the new generation rapid and low firecopper clay; the Prometheus® Copper Clay.

Prometheus® Copper Clay is an extraordinary medium that will transform your imagination into pure copper fine art and jewelry objects. You can easily shape your clay by hand or using some simple tools, or even turn it on a potter’s wheel. Firing Prometheus® Copper Clay is easier than ever; you simply need 30 minutes at 920°C or 90 minutes at 850°C or 10 minutes with a Torch.

Prometheus® Copper Clay
  • can be stored at room temperature
  • does not stick to hands at normal consistency
  • gives you long working time by its slow drying character
  • does not need long firing hours
  • does not need high firing temperatures
  • does not need a firing pan or activated carbon
  • does not need large and programmable kilns
What is Prometheus® Copper Clay?
Prometeus® Copper Clay is a claylike material which turns into pure, solid copper when fired in the kiln. It is a mixture of micron sized copper powder, water, and organic binder. It can be formed by hand, rolled into a sheet or a rope. It can be molded, textured, even turned on a potter's wheel. Prometeus® Copper Clay can be fired with most lab-created gemstones (cubic zirconias), pre-tested natural stones, glass beads, ceramic porcelain and Prometheus® Copper Clay . It is also suitable for enamelling. 

When PCC® is fired in a kiln, the organic binder evaporates, burns away and you’re left with pure, solid copper. Brush it, if needed pickle it, to remove any firescale, and finally polish. 

You can create unique jewellery, ornaments, hollow ware, statutes and many other decorative objects with PCC®. Any thing you create with PCC® is a piece of art. Combine it with your imagination, and let your fingers do the rest! 
Working with Prometheus® Copper Clay

Working with PCC® is similar to working with Prometheus® Bronze Clay, polymer clays, modelling dough, flower dough and ceramic clays. It is very easy to use. 

Wet Stage

At normal consistency, PCC® does not stick to hands or plastic working surfaces. However, oiling your fingers and the working surface lightly is useful, and would not harm your clay. Olive oil is preferable.
Remove the clay from its plastic bag and place it on a clean plastic surface or wax paper. Use your fingers, roller, spatulas, clay shapers, craft knives, tooth picks and other simple tools to shape it, texture it, or turn it on a potter’s wheel. You can texture the clay with rubber stamps, texture mats, leaves, paper, and other interesting textures. 
When you work with the clay out of the packet it is called “The Wet Stage”. Try to not work at this stage for too long, to stop your clay from drying out; but don’t rush your work, PCC® gives you enough time to play. However, if you detect any cracks on the surface, apply some water straight away with a brush or spray, and fill the cracks with a little paste to repair them. 
To join two pieces together, simply wet the points that will touch, or add a little paste (to make paste, simply mix a little clay with a little water until it is the consistency of thick youghurt). If the two pieces are dry, wet the touching points, and paste to create a secure bond.
Store any unused clay in a plastic bag with a zipper to prevent it from drying out. Place any offcuts in the bag straight away whilst you’re working, and keep it closed tight. If you’re not planning to work with the clay for a while, put the sealed plastic bag in a jar with a tight lid. Placing a wet sponge to the bottom of the jar will keep your clay at a good condition, until your next usage. If you are storing it for a long time, keep an eye on the sponge and add water if needed.


Drying

Before firing the bronze clay, you need to dry it completely. A hair dryer or putting it on top of a kiln will do it well. Hot-plates or food dehydrators work well too.
To check if the clay is completely dried, put the hot clay (straight from drying) on a cold mirror. After 10-20 seconds, move it and check that there is no condensation on the mirror. This test is especially important for big and thick pieces. If the piece is not dried completely, then it can crack, break or have bubbles on the surface while firing. 
We don’t recommend fast drying for large piece, as it may cause cracks. For these, it is recommended to leave them in room temperature for a few hours and then continue drying at moderate temperatures. 
Dry Stage

Whilst the dried PCC® is strong, you still need to take some care when working with it. You can carve designs on the surface, file it, grind it, drill holes with hand tools or rotary tools and engravers. To join dried pieces, wet the joining points with a brush and apply some paste. After completing your design, it is easy to sand uneven surfaces, using sand papers, and sanding sponges. It is a lot easier to do this step now - before you have fired the clay!
Firing Prometheus® Copper Clay

You have 3 choices for firing PCC®:

1. Conventional Method (*)

Place the dried piece (or pieces) on a stainless steel mesh and put it in to the pre-heated to 920 deg.C/1700 deg.F. (**) Wait for the kiln to raise up to its target temperature again, then start timing your firing for 30 minutes.

When the firing is completed, take out the piece, put it on a heat proof surface and wait for it to cool down or much better, quinch it in water while it is hot. (***) Most of the fire scale leaves the piece. If any left, leave it in hot pickling solution for some time.

(*) This method is recommended especially for large pieces; statuetts etc.,
(**) Most kilns are cooler near the front door, so put them close to the back of the heating chamber.
(***) Be aware of water vapour.



2. Carbon Method 

This is a 2-step-method.

Step.1 Place the dried piece (or pieces) on a stainless steel mesh and put it in to the pre-kiln at 500 deg.C/ 932 deg.F, or on a kitchen stove. Fire it for 10 minutes, take it on to a fire proof surface and let it cool down.

Step.2 Put aproximately 3 cm. of activated carbon to the bottom of a steel container. Place the pieces with at least 1.5 cm space between each other and fill the container with activated carbon, close it and put it into the preheated kiln to 850°C / 1570°F. Let the kiln raise to the target temperature again and fire it for 90 minutes. When the firing is completed, either leave it to cool down in the kiln or, carefully take it out and leave it on a heat isolated surface untill it is cold enough to take your pieces out. One other firing schedule is 800°C / 1472°F for 2 hours which is preferable when PCC® is combined with PBC®.




3. Torch Firing Method 

Place the dried piece on a stainless steel mesh. Put the mesh on a fiber brick or a thick construction brick. Fire the piece homogenously at a light-orange colour for 5-10 minutes according to the size of the piece. Avoid melting. After firing is completed, eather leave it to cool down or quinch in water. Leave in hot Picklean® solution to get rid of any fire scale if any left.





Finishing Prometheus® Copper Clay 

Brush your piece with a metal brush and, if necessary, put it in hot pickling solution. (*) After pickling, rinse the piece thoroughly with water and dry. This will give you a nice warm reddish copper color. You can also use many different patina solutions to give you other colours. 
(*) We recommend Picklean® granules. Mix one table spoon of Picklean® to a glass of hot water and leave your piece in it for some time. 

Polish the piece with a burnisher, polishing papers, a thumbler or polishing motor. Using polishing compounds can give extra shine to your works.
 

 
 
Wij gebruiken cookies om de gebruikerservaring te verbeteren of om advertenties te kunnen tonen. Door gebruik te maken van deze website ga je hiermee akkoord. Privacy & Cookiebeleid
SLUITEN